ServicesEquipment Installation
Pool Equipment Installation in Coolidge
When a pump, filter or heater has reached the end of its life, we replace it with equipment matched to your pool's volume and plumbing. Our crew handles the whole install, from the old unit out to the first clean startup, and leaves the pad tidy.
Replacing equipment the careful way
Most pool equipment fails slowly, then all at once. A pump motor that has been running hot for a season seizes, a filter tank cracks along a seam, or a monsoon storm sends a surge through the pad and a control board stops responding. When that happens, you want a clear answer about what to replace and what can stay.
We look at the whole system before recommending anything. A new pump has to suit the pipe size, the filter and the length of the plumbing run, or it will be loud, inefficient and hard on the rest of the pad. We are ROC licensed, and every installation is done in-house by our own people, never handed to a subcontractor.
If the damaged part can be fixed for a sensible price, we will say so and point you to our pool repair service instead.
What an installation includes
- 01
Variable-speed pumps
Current federal efficiency rules mean most replacement pumps are variable-speed. We set the speed schedule for your pool so it filters properly at low, quiet speeds and only runs high when it needs to.
- 02
Filters of every type
Cartridge, sand and DE filters, sized to the pump's flow. An undersized filter clogs fast in our dusty spring and summer, so we size with a margin.
- 03
Heaters and heat pumps
Gas heaters and electric heat pumps, with clearances checked, connections made and the unit tested under load before we leave.
- 04
Salt chlorine generators
We install the cell and control unit, set the output for your pool and explain how often the cell needs inspecting.
- 05
Automation and timers
Timers and automation systems wired so pump, heater and lights run on a schedule you can understand and change yourself.
- 06
Plumbing and electrical tie-in
New unions, valves and PVC where the old plumbing is brittle, plus proper bonding and grounding on every new component.
Questions about Equipment Installation?
Call(520) 210-5562Signs your equipment is due for replacement
Grinding or screeching pump
Worn motor bearings make a steady grinding noise. On older single-speed pumps, replacing the whole unit often makes more sense than a new motor.
Trouble after a storm
Lightning surges and blowing debris during monsoon season can knock out control boards, timers and motors. If something stopped working after a storm, we check what was damaged and what still tests fine.
Cracked or weeping tanks
Sun-faded filter tanks and pump housings grow brittle. A hairline crack that drips today can split under pressure later.
Pressure that will not settle
If the filter gauge climbs quickly after every cleaning, the filter may be too small or the media worn out.
Heater that will not fire
Repeated ignition faults, scorched wiring or a corroded heat exchanger usually point to replacement rather than another repair.
How installation day runs
- 1
Assessment and quote
We look at the pad, measure the plumbing and note the electrical supply. You get a written quote that lists the equipment and labor separately.
- 2
Removal and prep
We shut off power at the breaker, drain the lines and remove the old equipment. We haul it away rather than leaving it beside the house.
- 3
Install and connect
New equipment is set level on the pad and plumbed with fresh unions and valves. We then wire it and tie each component into the pool's grounding system. Electrical work follows code, and we tell you up front if your town requires a permit.
- 4
Startup and walkthrough
We prime the system, check for leaks, set the schedule and watch pressure readings. Before we leave, we show you the controls and what normal sounds and readings look like.
What shapes the cost of new equipment
Two installations of the same pump can be priced quite differently because of what surrounds it. We explain each line on the quote so you can see where the money goes. The quote is free and comes by phone after we have seen your pad.
- The equipment itself
- Pump horsepower, filter size and heater output vary widely. We recommend what your pool needs, not the largest unit available.
- Condition of the plumbing
- Sun-damaged or mismatched PVC often has to be replaced around the new unit. We show you what we find before adding it.
- Electrical needs
- A heat pump or new automation may need a dedicated circuit or upgraded wiring, which adds time and materials.
- Pad layout and access
- Tight side yards, crowded pads or equipment that has to be repositioned take longer to work around.
Equipment installation questions
Should I repair my pump or replace it?
It depends on the age of the pump and what failed. A failed seal on a newer pump is usually worth fixing. An older single-speed pump with a burned motor is often better replaced with a variable-speed unit that costs less to run. We give you both options when both are reasonable.
My equipment stopped working after a monsoon storm. What should I do first?
Turn the power off at the breaker and leave it off until the equipment is checked. Running a damaged motor or board can make things worse. We test each component and tell you what was damaged and what is still sound, so you only replace what you need to.
Do you use subcontractors for installations?
No. All of our work is done in-house by our own crew. The person who quotes your job understands exactly how it will be installed.
How long does an installation take?
A straightforward pump or filter swap is usually finished in a single visit. Heaters, salt systems and automation take longer, especially if new wiring or plumbing is involved. We give you a realistic time frame with your quote.
Will new equipment change how I care for my pool?
Sometimes. A salt system changes how chlorine is added, and a variable-speed pump runs on a longer, slower schedule. We walk you through the changes, and our weekly pool cleaning service can keep everything balanced if you would rather not handle it yourself.
Talk through your equipment with us
Tell us what stopped working or what you are thinking of upgrading. We will come look at your pad and give you a clear, written recommendation.